当前位置:IBM(000-232)题库

问题:

[单选]

The system administrator wants to use a new jfslog /dev/fs1log with the filesystem /test/fs1 on the testvg volume group. The following commands were used to create the log and assign it to the filesystem: 
(1)mklv -t jfslog -y /dev/fs1log testvg 1  
(2)chfs -a log=/dev/fs1log /test/fs1  
While trying to mount the /test/fs1 filesystem the administrator received the error: 
"Cannot mount /dev/fs1lv on /test/fs1: A system call received a parameter that is not valid".
What step did the administrator miss that most likely caused the error?()

A . Use the logform command to format /dev/fs1log as a jfslog
B . Use the chlv command to change the lv type of /dev/fs1log to jfslog
C . Use the chvg command to change the default jfslog of testvg to /dev/fs1log
D . Edit the /etc/filesystems file to change the log associated with /test/fs1 to /dev/fs1log

Given: Which three are valid?() p0 = p1;。 p1 = p2;。 p2 = p4;。 p2 = (ClassC)p1;。 p1 = (ClassB)p3;。 p2 = (ClassC)p4。 下列各项中不属于维纳提出的归因3个维度的是() 内外源。 普遍性。 可控性。 稳定性。 什么是三通阀? 现浇大模板住宅工程,该工程共8层,采用框架结构,建筑面积5285m2。该工程项目周围为已建工程,因施工场地狭小,现场道路按3m考虑并兼做消防车道,距离拟建房屋4m。搅拌机棚、砂石料只能在在建工程与已建工程之间的间隙堆放。施工供电设施已按照供电设计和施工总平面图布置完毕,并且建立了临时用电安全技术方案,方案内容包括:用电组织设计的全部资料;用电工程检查验收表;接地电阻、绝缘电阻和漏电保护器漏电动作参数测定记录表;定期检(复)查表。施工现场临时用电配置,以“三级配电、末级漏保”配电保护方式。 该项目在施工过程,发生如下几项事件: 事件一:在主体结构施工至第四层时,发现部分混凝土试块强度不合格,因此,施工单位聘请了有法定资质的检测单位进行现场实体检测,检测结果实体强度能够达到设计要求。 事件二:在外用电梯上升过程中,受七层阳台伸出的一根防护栏杆影响,架子工班长让正在脚手架上进行支模的木工王某立即拆除,王某随即进行拆除作业,结果不慎将钢管坠落,击中下方正在清理模板的张某,张某因安全帽被击穿,头部严重受伤,经抢救无效死亡。 事件一混凝土试块强度不合格的质量问题是否需要处理?并说明理由。 How can an administrator view the service bootlist?() service -l bootlist。 bosboot -ad service。 listboot -l service。 bootlist -om service。

The system administrator wants to use a new jfslog /dev/fs1log with the filesystem /test/fs1 on the testvg volume group. The following commands were used to create the log and assign it to the filesystem: 
(1)mklv -t jfslog -y /dev/fs1log testvg 1  
(2)chfs -a log=/dev/fs1log /test/fs1  
While trying to mount the /test/fs1 filesystem the administrator received the error: 
"Cannot mount /dev/fs1lv on /test/fs1: A system call received a parameter that is not valid".
What step did the administrator miss that most likely caused the error?()

参考答案:

  参考解析

本题暂无解析

相关题目:

在线 客服